Storage chamber for liquid refrigerant in the suction line (ISO 9897 numerical code 62265)

Component which allows proper air circulation throughout the thermal container (ISO 9897 numerical code 50250)

Primary device for screening air flow (ISO 9897 numerical code 62800)

Secondary device for screening air flow (ISO 9897 numerical code 62810)

Complete porthole assembly to permit passage of cold/hot air to and from the porthole thermal container (ISO 9897 numerical code 50010)

Device to detect pressure difference across evaporator coil for defrost initiation (ISO 9897 numerical code 61528)

A device which reinforces the securement of the locking bar assembly and limits the racking of the door frame (ISO 9897 numerical code 10640)

Device which allows air renewal to reduce the concentration of gas given off by respiration cargo (ISO 9897 numerical code 62630)

Anti-rack device in the form of an omega reinforcement running vertically, up the edge of the back door, which is connected to the horizontal members of the door frame by spigots (ISO 9897 numerical code 10650)

Anti-rack device, consisting of a plate at the top and bottom of the right-hand door which is connected to the left-hand door and door frame by spigots (ISO 9897 numerical code 10660)

Device in the transverse members of a door frame, and the left-hand door in the plate system, over which the anti-rack device fits (ISO 9897 numerical code 10670)

Air screen intermediate panel assembly separating the air inlet from the air outlet (ISO 9897 numerical code 50150)

Hinged air screen flap on which the valve assembly is mounted permitting access to the valve and behind inlet or outlet screen (ISO 9897 numerical code 50160)

Gasket for air screen flap (ISO 9897 numerical code 50165)

Air screen flag hinge (ISO 9897 numerical code 50170)

Air screen flap locking device (ISO 9897 numerical code 50180)

Inlet or outlet air screen panel to ensure proper air distribution in the container (ISO 9897 numerical code 50190)

Compressor assembly and its driving electric motor (ISO 9897 numerical code 60010)

Electronic board which amplifies the data coming from the various sensors (ISO 9897 numerical code 61700)

Box which contains all the electric and electronic equipment components of the controller (ISO 9897 numerical code 62670)

Electronic board which controls the motor starting sequence and the electric current of the modulating valves (ISO 9897 numerical code 61670)

Opening panel of the controller box (ISO 9897 numerical code 62680)

Seal designed to close the controller box door tightly (ISO 9897 numerical code 62690)

Hinge supporting controller box door (ISO 9897 numerical code 62695)

Electronic board which manages all the controller functions (ISO 9897 numerical code 61640)

Glass mounted in controller box door (ISO 9897 numerical code 62696)

Box which contains all the electrical components for power control and recorder (ISO 9897 numerical code 62640)

Opening panel of the electrical box (ISO 9897 numerical code 62650)

Seal designed to close the electrical box door tightly to keep water out (ISO 9897 numerical code 62660)

Hinge supporting electrical control box (ISO 9897 numerical code 62664)

Cover to guard against accidental contact with high-voltage circuits (ISO 9897 numerical code 62738)

Main electronic board which is connected to all the other electronic boards (ISO 9897 numerical code 61630)

Electronic board which controls the power supply and the temperature inside the container (ISO 9897 numerical code 61660)

Part of the motor to support the revolving rotor in the centre of the stator (not specified elsewhere) (ISO 9897 numerical code 60300)

Part of the motor to support the revolving rotor in the centre of the stator (not specified elsewhere) (ISO 9897 numerical code 60610)

Part of the motor to support the revolving rotor in the centre of the stator (not specified elsewhere) (ISO 9897 numerical code 60910)

Sensor which indicates the temperature of the gas leaving the evaporator to the expansion valve (ISO 9897 numerical code 62140)

Electronic board which controls the reversal of the phase sequence (ISO 9897 numerical code 61650)

Box which contains the temperature recorder (ISO 9897 numerical code 62700)

Opening panel of the recorder box (ISO 9897 numerical code 62710)

Seal designed to close the recorder box tightly (ISO 9897 numerical code 62720)

Hinge supporting recorder box door (ISO 9897 numerical code 62726)

Glass mounted in recorder box door (ISO 9897 numerical code 62725)

Electronic board to which all the various relays are connected (ISO 9897 numerical code 61690)

Support which holds crankshaft in place (ISO 9897 numerical code 60035)

Electronic board which controls the temperature inside the container (ISO 9897 numerical code 61680)

Electronic device for regulation of controlled-atmosphere system (ISO 9897 numerical code 62880)

Drier in controlled-atmosphere system (ISO 9897 numerical code 62830)

Heater in controlled-atmosphere system (ISO 9897 numerical code 62840)

Apparatus for accumulating electricity which allows the condenser motor to be started (ISO 9897 numerical code 61110)

Apparatus for accumulating electricity which allows the compressor motor to be started (ISO 9897 numerical code 61090)

Compressor in controlled-atmosphere system (ISO 9897 numerical code 62820)

Series of pipes connected in rows to increase heat exchange (ISO 9897 numerical code 60510)

Series of pipes connected in rows to increase heat exchange (ISO 9897 numerical code 60810)

Apparatus for accumulating electricity which allows the evaporator motor to be started (ISO 9897 numerical code 61100)

Switch to shut down operation of refrigeration and controlled-atmosphere unit when container door is opened (ISO 9897 numerical code 62980)

Safety device which breaks the 230 V electric circuit if a fault develops (ISO 9897 numerical code 61055)

Safety device which breaks the 460 V electric circuit if a fault develops (ISO 9897 numerical code 61050)

Bracket holding condenser coil in place (ISO 9897 numerical code 60516)

Filter to remove carbon dioxide gas (ISO 9897 numerical code 62970)

Device to detect carbon dioxide in controlled-atmosphere system (ISO 9897 numerical code 62900)

Tank containing carbon dioxide gas (ISO 9897 numerical code 62870)

Fittings located at the corners of containers providing means of supporting, stacking, handling, and securing the container [from ISO 830] (ISO 9897 numerical code 10280)

Fins expediting heat transfer from tubes (ISO 9897 numerical code 60555)

Fins expediting heat transfer from tubes (ISO 9897 numerical code 60855)

Threaded receptacle in front corner post for clip-on generator set clamping device (ISO 9897 numerical code 50640)

Safety device to switch off the system in case of pressure above a fixed limit (ISO 9897 numerical code 60160)

Contactor which connects or breaks the heating resistor electric circuit according to the control box order (ISO 9897 numerical code 61210)

Receptable in front header for clip-on generator set clamping device (ISO 9897 numerical code 50630)

Electronic container identification device permanently affixed to the container (ISO 9897 numerical code 50710)

Contactor which connects or breaks the compressor electric circuit according to the control box order (ISO 9897 numerical code 61180)

Contactor which connects or breaks the compressor high-speed electric circuit according to the control box order (ISO 9897 numerical code 61200)

Contactor which connects or breaks the compressor low-speed electric circuit according to the control box order (ISO 9897 numerical code 61190)

Safety device to switch off the system in case of oil pressure below a fixed limit (ISO 9897 numerical code 60180)

Safety device to switch off the system in case of pressure below a fixed limit (ISO 9897 numerical code 60170)

Components in the base structure of a container supporting the floor (ISO 9897 numerical code 10370)

Components fixed to the cross-member ends for their securing to the bottom side rails by rivets or special bolts (ISO 9897 numerical code 10380)

Other regulation/control devices not listed (ISO 9897 numerical code 61800)

Lower flange of a cross-member (ISO 9897 numerical code 10390)

Short cross-member extending between bottom side rail and gooseneck tunnel rail (ISO 9897 numerical code 10425)

Complete transvers section of a cross-member (ISO 9897 numerical code 10420)

Upper flange of a cross-member (ISO 9897 numerical code 10400)

Web of a cross-member (ISO 9897 numerical code 10410)

Carbon electrical conductor that makes sliding contact on the collector (ISO 9897 numerical code 60290)

Carbon electrical conductor that makes sliding contact on the collector (ISO 9897 numerical code 60600)

Carbon electrical conductor that makes sliding contact on the collector (ISO 9897 numerical code 60900)

Conductor maintaining contact between the rotor and the stator (ISO 9897 numerical code 60280)

Conductor maintaining contact between the rotor and the stator (ISO 9897 numerical code 60590)

Conductor maintaining contact between the rotor and the stator (ISO 9897 numerical code 60890)

Point where electrical/electronic components are connected (ISO 9897 numerical code 61230)

Points where electric/electronic components are connected (ISO 9897 numerical code 61780)

Device which allows sampling of air from the container to measure the concentration of carbon dioxide (ISO 9897 numerical code 62740)

Fitting in the corner post into which the lower part of a clip on a generator set is secured (ISO 9897 numerical code 10270)

Vertical structural member at either side of an “end frame” of a container joining a top and a bottom corner fitting (and thereby forming a “corner structure”) [from ISO 830] (ISO 9897 numerical code 10260)

Reinforcement between the corner fitting and the corner post, particularly in a platform-based container (ISO 9897 numerical code 10290)

Contactor which sets up the phase order according to the phase reversal system (ISO 9897 numerical code 61220)

The inner part of a two- or multi-component corner post (ISO 9897 numerical code 10300)

The portion of the exterior part of the rear corner post that encircles the door hinges (ISO 9897 numerical code 10310)

Hinge component permanently attached by welding to the rear corner post (ISO 9897 numerical code 10320)

The outer part of a two- or multi-part corner post (ISO 9897 numerical code 10330)

The vertical reinforcement of a corner post, normally welded to the corner post outer part (ISO 9897 numerical code 10340)

Single component of a one-piece corner post (ISO 9897 numerical code 10350)

Complete transvers section of a corner post (ISO 9897 numerical code 10360)

Controller whose functions are governed by a microprocessor chip (ISO 9897 numerical code 61415)

Contactor which connects or breaks the compressor electric circuit according to the control box order (ISO 9897 numerical code 61120)

Contactor which connects or breaks the compressor high-speed electric circuit according to the control box order (ISO 9897 numerical code 61140)

Contactor which connects or breaks the compressor low-speed electric circuit according to the control box order (ISO 9897 numerical code 61130)

Connection points for regulation electrical components (ISO 9897 numerical code 61775)

Rotating member that transmits force to pistons (ISO 9897 numerical code 60034)

Device which controls essential functions of the refrigeration unit, especially temperature (ISO 9897 numerical code 61410)

Contactor which connects or breaks the evaporator electric circuit according to the control box order (ISO 9897 numerical code 61150)

Contactor which connects or breaks the evaporator high-speed electric circuit according to the control box order (ISO 9897 numerical code 61170)

Contactor which connects or breaks the evaporator low-speed electric circuit according to the control box order (ISO 9897 numerical code 61160)

Heat exchanger in which refrigerant is changed from gas to liquid by water cooling (ISO 9897 numerical code 60700)

Chamber in which one piston moves (ISO 9897 numerical code 60080)

Gasket to seal the cylinder head cover on the compressor body (ISO 9897 numerical code 60070)

Cover of the piston chamber above the valve plate (ISO 9897 numerical code 60040)

Solenoid coil which operates opening/closing of one cylinder unloader (ISO 9897 numerical code 60060)

Device to cut off the cylinder or to allow communication between high pressure and low pressure to decrease the compressor capacity (ISO 9897 numerical code 60050)

Entire door, including stiffeners, but not including hardware and gaskets (ISO 9897 numerical code 12050)

Entire door, including stiffeners, hardware (except hinges), and gaskets (ISO 9897 numerical code 12060)

Entire door that is fitted with corrugated panels, including stiffeners, hardware (except hinges) and gaskets (ISO 9897 numerical code 10586)

The holes in the door handle catch and door handle retainer through which the customs seal is secured (ISO 9897 numerical code 10620)

Flexible air seal to retard gas transfer through door (ISO 9897 numerical code 50136)

End frame structural components in a hinged assembly that may be lowered to the floor surface of a platform-based container (ISO 9897 numerical code 12045)

Entire door that is fitted with flat panels, including stiffeners, hardware (except hinges) and gaskets (ISO 9897 numerical code 10585)

Complete door frame with all component pieces (ISO 9897 numerical code 12070)

A web for strenghtening the rear or front lower rail (ISO 9897 numerical code 11582)

Set of door locking rods, cams, and cam retainers (keepers), including mounting hardware, for a single door (ISO 9897 numerical code 10509)

Bush(ing) inserted into door hinge for smooth operation (ISO 9897 numerical code 10505)

A component of the door handle lock assembly, fixed to the door and which the door handle is engaged when the doors are closed (ISO 9897 numerical code 10600)

The device which can be sealed for compliance with the CCC and which locks the door in the closed position (ISO 9897 numerical code 10590)

A component of the door handle lock assembly, which rotates and holds the door handle in the closed position, and through which the seal is secured (ISO 9897 numerical code 10610)

Knob fitted to shaft of defrost interval selector switch (ISO 9897 numerical code 61536)

Switch to select choice of defrost intervals (ISO 9897 numerical code 61535)

Flexible bladder, fitted to the underside of a T-floor drain, that opens and reseals by hydrostatic pressure to expel fluids that drain from the interior of a thermal container (ISO 9897 numerical code 50395)

Device fixed underneath the evaporator coil to collect defrost water (ISO 9897 numerical code 62610)

Electrical resistors provided on the drain port for defrosting (ISO 9897 numerical code 60861)

Door edge plate preventing opening the left-hand door unless the right hand door is open (ISO 9897 numerical code 10635)

Rivets used to attach door plate (ISO 9897 numerical code 10636)

Plug and chain assembly for floor drain (ISO 9897 numerical code 50385)

Tensioning device to impart torque to a pulley (ISO 9897 numerical code 60135)

Device which allows the refrigerant charge to be dried (ISO 9897 numerical code 62190)

Link device for holding door in open position (ISO 9897 numerical code 10632)

Mounting bracket, attached to door panel, that holds the door retainer (ISO 9897 numerical code 10587)

Tube which drains water out of the unit (ISO 9897 numerical code 62620)

A device which retains the door in the open position (ISO 9897 numerical code 10630)

Horizontal reinforcing member of door, installed on bottom edge (ISO 9897 numerical code 11625)

Horizontal reinforcing member of door, installed along vertical midline of door (ISO 9897 numerical code 11626)

Vertical reinforcing member of door, installed along hinge side (ISO 9897 numerical code 11627)

NOTE - Preliminary assignment; to be defined in a future edition (ISO 9897 numerical code 11623)

NOTE - Preliminary assignment; to be defined in a future edition (ISO 9897 numerical code 10588)

Horizontal reinforcing member of door, installed on bottom edge (ISO 9897 numerical code 11628)

Vertical reinforcing member of door (ISO 9897 numerical code 11629)

Electrical resistors provided on the drain tube for defrosting (ISO 9897 numerical code 60859)

Complete assembly of all endwall (not door) panels, including posts and stringers, at one end of container (ISO 9897 numerical code 12020)

Power line (460 V) to transmit electrical power to the refrigeration unit (ISO 9897 numerical code 61020)

Battery for an electronic container identification device requiring power supply (active device) (ISO 9897 numerical code 50720)

Power line (230 V) to transmit electrical power to the refrigeration unit (ISO 9897 numerical code 61025)

Identifying label on 460 V power cable (ISO 9897 numerical code 61026)

Identifying label on 230 V power cable (ISO 9897 numerical code 61027)

Retainer for electrical diagram (ISO 9897 numerical code 62666)

Schematic or functional diagram of wiring (ISO 9897 numerical code 62665)

Rotating assembly supporting collapsible end frame of platform-based container (ISO 9897 numerical code 10485)

Other electrical power devices not listed (ISO 9897 numerical code 61250)

Device to connect the 230 V power cable to the power supply receptacle (ISO 9897 numerical code 61015)

Device to connect the 460 V power cable to the power supply receptacle (ISO 9897 numerical code 61010)

Electrical connections which receive the power supply directly from the mains (ISO 9897 numerical code 61080)

Device which records the operating conditions of the unit for retrieval by electronic means (ISO 9897 numerical code 61445)

Filter to remove ethylene gas (ISO 9897 numerical code 62960)

Device which controls the defrost cycle by sensing temperature (ISO 9897 numerical code 61527)

Assembly of blades to produce a flow of air through the coil (ISO 9897 numerical code 60650)

Assembly of blades to produce a flow of air through the coil (ISO 9897 numerical code 60950)

Structure of the refrigeration unit (ISO 9897 numerical code 62510)

Volume of refrigerant inside the refrigeration unit (ISO 9897 numerical code 62270)

Retainer for fuses (ISO 9897 numerical code 61735)

Hat or omega steel section running longitudinally, sometimes used with either plywood or plank floorings (ISO 9897 numerical code 10700)

Element fixing the compressor/motor assembly to the frame (ISO 9897 numerical code 60340)

Element fixing the compressor/motor assembly to the frame (ISO 9897 numerical code 60640)

Element fixing the compressor/motor assembly to the frame (ISO 9897 numerical code 60940)

Reinforced pockets running transversally across the base of a container, piercing the bottom side rails at prescribed positions to permit the entry of the tines of fork lift de-vices for lifting and carrying the container (ISO 9897 numerical code 10850)

Flooring of (vertically) laminated plank (ISO 9897 numerical code 10710)

Flange formed at the bottom edge of the forklift pocket (ISO 9897 numerical code 10860)

The plated welded to the top of the fork lift pocket (ISO 9897 numerical code 10880)

The plate welded to the bottom of each fork lift pocket entrance (ISO 9897 numerical code 10870)

Complete transverse section of a forklift pocket (ISO 9897 numerical code 10910)

Flange formed at the top edge of the forklift pocket (ISO 9897 numerical code 10890)

The web or side of the fork pocket (ISO 9897 numerical code 10900)

Other frame devices not listed (ISO 9897 numerical code 62780)

Flooring of wood plank (ISO 9897 numerical code 10690)

Flooring of plywood (ISO 9897 numerical code 10720)

NOTE - Preliminary assignment; to be defined in a future edition (ISO 9897 numerical code 10675)

Angle attached to bottom side rail which supports edge of floor (ISO 9897 numerical code 11630)

Longitudinal steel floor sections, used in conjunction with alternating wood sections (ISO 9897 numerical code 11640)

Steel plate secured inside doorway to protect flooring against cargo handling equip-ment (ISO 9897 numerical code 10730)

Nozzle set in the side (or front) panel which permits fumigation of the container (ISO 9897 numerical code 11840)

Device which opens the piping circuit in case of over-pressure (ISO 9897 numerical code 62200)

Short piece of wire which melts and breaks the control circuit if a fault develops in it (ISO 9897 numerical code 61730)

Complete wooden floor (ISO 9897 numerical code 10680)

Floor of wood planks combined with longitudinal omega sections (ISO 9897 numerical code 10740)

Seals between the refrigeration unit frame and the container frame (ISO 9897 numerical code 62590)

Cover piece for corner joint on door gasket (ISO 9897 numerical code 10472)

Device which indicates the discharge pressure of the compressor (ISO 9897 numerical code 62210)

Inner gasket of a multi-gasket system, usually on thermal containers (ISO 9897 numerical code 10450)

Whole part of a multi-leaf gasket, combining the effects of both the inner and outer gaskets, usually found on thermal containers (ISO 9897 numerical code 10460)

Device which protects the evaporator fan inside the container (ISO 9897 numerical code 62550)

Device which protects the condenser fan outside the container (ISO 9897 numerical code 62530)

A strip running inside a gasket around a door through which fasteners are passed to secure the gasket to the door edge (ISO 9897 numerical code 10440)

Device which indicates the suction pressure of the compressor (ISO 9897 numerical code 62220)

The seal running round the edge of a door and other fittings needed to ensure ist proper fixing (ISO 9897 numerical code 10430)

Outer part of the multi-leaf gasket, usually on thermal containers (ISO 9897 numerical code 10470)

Hatch, when opened, which is used to discharge bulk cargo (ISO 9897 numerical code 10930)

Hatch, when opened, through which bulk cargo is loaded (ISO 9897 numerical code 10940)

Panel which can be removed to access the heater coils and drain section from outside the container (ISO 9897 numerical code 62525)

Device for attaching a clip-on refrigeration unit to the lower receptacle of a container (ISO 9897 numerical code 62770)

Holes in the hatch handle catch and hatch handle retainer through which the customs seal is secured (ISO 9897 numerical code 11010)

Device for attaching a clip-on refrigeration unit to the upper receptacle of a container (ISO 9897 numerical code 62760)

Cover that closes off a hatch (ISO 9897 numerical code 10950)

Electrical resistors for defrosting the drain pan or heating the container (ISO 9897 numerical code 60857)

Sleeve fitted to the discharge hatch for discharge (ISO 9897 numerical code 10970)

Extended header plate used to protect roof from damage (ISO 9897 numerical code 11650)

Device which allows exchange of heat between hot gas and cold liquid in order to increase the efficiency of the refrigeration system (ISO 9897 numerical code 62150)

Fitting on which the door rotates (ISO 9897 numerical code 10480)

Hinge component that is secured to the door and holds the pin (ISO 9897 numerical code 10490)

Hinge component attaching the blade to the lug (ISO 9897 numerical code 10500)

Gasket that seals the hatch cover (ISO 9897 numerical code 10960)

Component of the hatch handle locking assembly, fixed to the hatch cover, through which the customs seal is secured (ISO 9897 numerical code 10980)

Fitting on which the hatch cover rotates (ISO 9897 numerical code 10990)

Device which retains the hatch-locking handle in the closed position, and through which the customs seal is secured (ISO 9897 numerical code 11000)

Bar which holds the hatch cover closed (ISO 9897 numerical code 11020)

Handle which operates the hatch locking bar (ISO 9897 numerical code 11030)

Device that keeps the hatch cover secured closed (ISO 9897 numerical code 11040)

Clock which records the compressor running hours (ISO 9897 numerical code 61490)

Chain securing header pin handle to removable header member (ISO 9897 numerical code 11669)

Hinge pin on removable header (ISO 9897 numerical code 11668)

Rail for hanging cargo in the container (ISO 9897 numerical code 50600)

Bars for hanging cargo in the container (ISO 9897 numerical code 50610)

Hook for hanging cargo in the container (ISO 9897 numerical code 50620)

Apparatus for controlling humidifier (ISO 9897 numerical code 62930)

Apparatus for keeping the humidity in a container within limits (ISO 9897 numerical code 62940)

Electrical resistors for defrosting the evaporator or heating the inside of the container (ISO 9897 numerical code 60856)

Structural fastener for securing components and performing repairs (ISO 9897 numerical code 11915)

Screws, nuts, and bolts (ISO 9897 numerical code 11900)

Screws, nuts, and bolts (ISO 9897 numerical code 62580)

Screws, nuts, bolts, and similar items (ISO 9897 numerical code 90335)

Front inside panel of the container (ISO 9897 numerical code 62560)

Material which prevents heat transfer in the suction line (ISO 9897 numerical code 61260)

Entire frame structure of generator set (ISO 9897 numerical code 80830)

Enclosure for main control circuits (ISO 9897 numerical code 80530)

Weather-protective enclosure (ISO 9897 numerical code 80800)

Opening access cover (ISO 9897 numerical code 80810)

Receptacle for forklift truck blade, used in lifting (ISO 9897 numerical code 80820)

Miscellaneous fasteners and routing fittings (ISO 9897 numerical code 81520)

Male frame securement fitting (ISO 9897 numerical code 80840)

Decals and plates conveying information (ISO 9897 numerical code 81530)

Components of generator sets not specified elsewhere (ISO 9897 numerical code 81540)

Flat metal enclosure (ISO 9897 numerical code 80860)

Frame securement fitting that secures by pressure (ISO 9897 numerical code 80850)

Electrical safety device for 380/460 V circuit (ISO 9897 numerical code 80510)

Board incorporating printed circuits and related electronic components (ISO 9897 numerical code 80520)

Electrical safety device for 190/230 V circuit (ISO 9897 numerical code 80500)

Electrical safety device for 12 V circuit (ISO 9897 numerical code 80490)

Flexible conduit for flow of coolant (ISO 9897 numerical code 81310)

Flexible conduit for fuel flow (ISO 9897 numerical code 81150)

Flexible conduit for oil (ISO 9897 numerical code 81070)

Miscellaneous engine piping not otherwise defined (ISO 9897 numerical code 80220)

Female connector on charger (ISO 9897 numerical code 80450)

Restraining bar holding battery in place (ISO 9897 numerical code 80480)

Seal for exciter cover (ISO 9897 numerical code 80550)

Male connector on charger (ISO 9897 numerical code 80440)

Electrical component to bring fuel to combustion temperature (ISO 9897 numerical code 80630)

Device for measuring operating time of engine (ISO 9897 numerical code 80640)

Securing fasteners for battery (ISO 9897 numerical code 80470)

Switch for sensing water temperature (ISO 9897 numerical code 81340)

Generator of alternating current (ISO 9897 numerical code 80950)

Induction coil within starter motor (ISO 9897 numerical code 80700)

Current measurement device (ISO 9897 numerical code 80430)

Self-contained power storage device (ISO 9897 numerical code 80460)

Voltage control device (ISO 9897 numerical code 80670)

Motor used to operate engine until ignition occurs (ISO 9897 numerical code 80690)

Female connector for 190/230 V circuit (ISO 9897 numerical code 80650)

Female connector for 380/460 V circuit (ISO 9897 numerical code 80660)

Wiring or harness not otherwise defined (ISO 9897 numerical code 80770)

Filter to remove impurities in fuel line (ISO 9897 numerical code 81180)

Device for measuring amount of fuel in tank (ISO 9897 numerical code 81130)

Element to raise fuel to a temperature at which flow can occur (ISO 9897 numerical code 81140)

Device to transport fuel to fuel injectors (ISO 9897 numerical code 81200)

Orifice through which fuel is introduced into cylinders (ISO 9897 numerical code 81210)

Manually operated device for forcing fuel flow (ISO 9897 numerical code 81170)

Filter to remove impurities within engine (ISO 9897 numerical code 81120)

Filter downstream of fuel filter (ISO 9897 numerical code 81190)

Receptacle for fuel (ISO 9897 numerical code 81160)

Seal on cylinder head cover (ISO 9897 numerical code 80050)

Seal on exhaust manifold (ISO 9897 numerical code 80170)

Seal on cylinder block front cover (ISO 9897 numerical code 80040)

Seal on cylinder head (ISO 9897 numerical code 80060)

Seal on intake manifold (ISO 9897 numerical code 80200)

Seal on oil pan (ISO 9897 numerical code 81010)

Rubber sealant in water pump (ISO 9897 numerical code 81330)

Securing device operated by pressure (ISO 9897 numerical code 81500)

Hardware securement fittings (ISO 9897 numerical code 81510)

Cover for coolant intake port on radiator (ISO 9897 numerical code 80270)

Hose used to transport coolant to/from radiator (ISO 9897 numerical code 80240)

Complete radiator and associated fittings (ISO 9897 numerical code 80250)

Cushioning device for radiator (ISO 9897 numerical code 80260)

Coolant flow regulator based on coolant temperature (ISO 9897 numerical code 80290)

Alternator and related components (ISO 9897 numerical code 80900)

Lubrication fitting for alternator rotor (ISO 9897 numerical code 80910)

Driving element of alternator rotor (ISO 9897 numerical code 80920)

Exciter field within alternator (ISO 9897 numerical code 80410)

Negative terminal of diode (ISO 9897 numerical code 80400)

Positive terminal of diode (ISO 9897 numerical code 80420)

Movable electrical induction coil (ISO 9897 numerical code 80930)

Fixed electrical induction coil (ISO 9897 numerical code 80940)

Entire engine (ISO 9897 numerical code 80000)

Complete engine (ISO 9897 numerical code 80130)

Miscellaneous bearing within engine. not otherwise defined (ISO 9897 numerical code 80100)

Cover enclosing cylinder head components (ISO 9897 numerical code 80150)

Filter for air entering engine combustion chamber (ISO 9897 numerical code 80140)

Drive belt for any engine pulley (ISO 9897 numerical code 80090)

Cooling fan for engine (ISO 9897 numerical code 80110)

Device for oil pressure measurement (ISO 9897 numerical code 81060)

Top portion of engine cylinders (ISO 9897 numerical code 80070)

Mounting for idler pulley (ISO 9897 numerical code 80190)

Bearings forming part of crankshaft (ISO 9897 numerical code 80030)

Device for cleansing oil (ISO 9897 numerical code 81050)

Noise-abatement device fitted in exhaust line (ISO 9897 numerical code 80210)

Piston and connecting rod, including pin (ISO 9897 numerical code 80230)

Exhaust piping attached directly to cylinder head (ISO 9897 numerical code 80080)

Connecting rod and associated bearing (ISO 9897 numerical code 80010)

Fuel strainer in engine bowl (ISO 9897 numerical code 80120)

Sump in which oil collects (ISO 9897 numerical code 81030)

Rotating member that transmits torque to generator (ISO 9897 numerical code 80020)

Bent piping within exhaust line (ISO 9897 numerical code 80160)

Pulley not driving another component, used for tensioning drive belt (ISO 9897 numerical code 80180)

Cover on exhaust pipe for preventing entry of water from atmosphere (ISO 9897 numerical code 80280)

(Self-explanatory) (ISO 9897 numerical code 81110)

Fluid used to prevent freezing of fuel (ISO 9897 numerical code 81100)

Indicator of depth of oil in pan (ISO 9897 numerical code 81040)

Lubricating fluid (ISO 9897 numerical code 81000)

Measurement device for oil temperature (ISO 9897 numerical code 81020)

Electrical switching device to control engine operation (ISO 9897 numerical code 80680)

Safety shutdown switch when operating temperature is too high (ISO 9897 numerical code 80720)

Safety shutdown switch when oil pressure is insufficient (ISO 9897 numerical code 80730)

Switch to start and stop engine operation (ISO 9897 numerical code 80740)

Switch to energize glow plugs (ISO 9897 numerical code 80760)

Switch to engage starter motor (ISO 9897 numerical code 80750)

Safety shutdown switch when water temperature is too high (ISO 9897 numerical code 80710)

Pump used when main water pump is not used (ISO 9897 numerical code 81320)

Fluid used to prevent freezing of coolant (ISO 9897 numerical code 81300)

Device for measuring coolant temperature (ISO 9897 numerical code 81380)

Device for regulating flow of coolant (ISO 9897 numerical code 81370)

Filter for removing water from fuel line (ISO 9897 numerical code 81360)

Coolant fluid (ISO 9897 numerical code 81350)

Entire set of exciter components (ISO 9897 numerical code 80560)

Enclosure for exciter (ISO 9897 numerical code 80570)

Cover for exciter assembly (ISO 9897 numerical code 80600)

Diode component of exciter rectifier (ISO 9897 numerical code 80620)

Electrical potential measurement device for exciter (ISO 9897 numerical code 80540)

Converter of 3-phase a.c. to d.c. (ISO 9897 numerical code 80580)

Resistive component within exciter (ISO 9897 numerical code 80610)

Receptacle into which exciter is plugged (ISO 9897 numerical code 80590)

Entire generator set, including all components (ISO 9897 numerical code 81400)

Gasket fitted to the inside of a gladhand (air coupling) to prevent air leaks (ISO 9897 numerical code 90315)

Flexible pneumatic cushioning device, pressurized by tractor air, in air ride suspension assembly (ISO 9897 numerical code 90015)

"Fittings for connecting air brake lines between vehicles
Alternative: Gladhand, 90310" (ISO 9897 numerical code 90010)

(See Air coupling, 90010 (ISO 9897 numerical code 90310)

Adjustable mechanical lever used to transmit brake chamber force to the brake cam shaft when brakes are applied. They are so designed that they can be adjusted to compensate for lining wear (ISO 9897 numerical code 90740)

Assembly of the gladhand, nipple and the threaded metal device used to attach them all to the front bolster. (ISO 9897 numerical code 91270)

The part of the lower (inner) landing gear leg comprising the pivot shaft and the foot. (ISO 9897 numerical code 91650)

Nut on the end of a wheel axle which retains the wheel bearings, wheel bearing cups, and wheel bearing lock washer. Code may also be used for intermediate nuts for securing wheel bearings to the axle. (ISO 9897 numerical code 90025)

Pin which secures two brake shoes in a foundation brake, and about which the brake shoes rotate when brake application is made (ISO 9897 numerical code 90016)

A short metal tube with male threads both ends used to attach the gladhand to the bulkhead fitting. (ISO 9897 numerical code 91260)

Suspension which utilizes flexible pneumatic cushioning bladders, which are pressurized by tractor air and regulated by height control valves or variable pressure regulators (ISO 9897 numerical code 90014)

Machined shaft at each end of the axle (ISO 9897 numerical code 90030)

Brake ABS valve (ISO 9897 numerical code 90116)

Device that locks the axle nut in the adjusted position. (ISO 9897 numerical code 91080)

Rectangular, square, or circular steel tubes with spindles pressed onto the ends about which wheels rotate (ISO 9897 numerical code 90020)

Part of a brake system normally used by the driver to apply and modulate the stopping force of the vehicle (ISO 9897 numerical code 90710)

The part of the chassis to which the front or rear container securing twist locks are mounted. (ISO 9897 numerical code 91350)

Parts of the braking system in which the forces opposing the movement or tendency to movement, of a vehicle are produced (ISO 9897 numerical code 90070)

Cylindrical rotating member of a wheel which is acted upon by frictional material (brake shoes) of the brake system (ISO 9897 numerical code 90080)

Hose which carries air from the tractor compressor through the chassis brake valve(s) to the reservoir (component 90680) (ISO 9897 numerical code 90092)

Plate which fits between the uprights in the bumper, to which the licence plate may be attached (ISO 9897 numerical code 90132)

Railing, mounted along the outside of the chassis between the landing gear assembly and the rear axle assembly, to guard against cyclists accidentally falling underneath (ISO 9897 numerical code 90040)

Flexible or rigid conductor for the transmission of air pressure in the brake system (ISO 9897 numerical code 90090)

Periodic safety inspection required by the California Highway Patrol. (ISO 9897 numerical code 91470)

Brake system (ISO 9897 numerical code 90060)

Kit containing the parts necessary for a brake overhaul. (ISO 9897 numerical code 91110)

Lining of the brake shoes that act upon the brake drum (ISO 9897 numerical code 90100)

Bracket attached to an axle for mounting the spring brake (component 90780) (ISO 9897 numerical code 90072)

Transverse structural member designed to support the container in a fixed position (ISO 9897 numerical code 90050)

Structure designed to provide rear-end impact protection (ISO 9897 numerical code 90130)

Component used to attach the torque rod to the axle. (ISO 9897 numerical code 91250)

Horizontal member at the base of the bumper, which is attached to the bumper uprights (ISO 9897 numerical code 90136)

Retaining device used with the rollers in S-cam type brake shoe installations. (ISO 9897 numerical code 91180)

Retaining device used between top and bottom brake shoes to pull the linings away from the brake drum surface when the brakes are released. (ISO 9897 numerical code 91210)

The part of the chassis to which the rear container securing twist locks are mounted. (ISO 9897 numerical code 91340)

Centre plate, either bolted or welded to the axle, to which the brake assembly is attached (ISO 9897 numerical code 90110)

Vertical stiffening members in the bumper (ISO 9897 numerical code 90134)

Box containing fittings for the chassis emergency and service brake connections and the electrical connector to which the lines from the towing vehicle may be connected (also called “Nose box”, 90580) (ISO 9897 numerical code 90170)

(See Connection box, 90170) (ISO 9897 numerical code 90580)

Nipple used for the introduction of grease into moving parts (ISO 9897 numerical code 90322)

Anti-theft device used in conjunction with the wheel lug nuts. (ISO 9897 numerical code 91450)

Electrical overload protection device which opens a circuit upon sensing excessive voltage or heat (ISO 9897 numerical code 90140)

A type of shock absorbing foot used at the bottom of the inner (lower) landing gear leg. (ISO 9897 numerical code 91220)

"Structural member on the front of a container chassis to serve as gathering device for guiding a container into its proper place on the chassis
Alternative: Horn, 90350" (ISO 9897 numerical code 90180)

(See Container guides, 90180) (ISO 9897 numerical code 90350)

Hollow cylinder which reduces friction at the rotation point of the brake S-cam through the brake spider (ISO 9897 numerical code 90104)

Label permanently affixed, usually to the forward left side of the chassis, stating that the vehicle conforms to all applicable safety standards in effect on the date of original manufacture (for example in United States, as required by National Highway Traffic Safety Administration) (ISO 9897 numerical code 90150)

Pin, which inserts through the drilled ends of the brake clevis, to retain the brake clevis (ISO 9897 numerical code 90078)

A locking device that retains the S-cam shaft in position. (ISO 9897 numerical code 91100)

Shaft having an S-shaped cam which moves brake rollers, thereby spreading shoes apart to make linings contact the brake drum (ISO 9897 numerical code 90105)

Tapered ring which holds a wheel bearing cone in which the bearings rotate (ISO 9897 numerical code 91010)

U-shaped metal shackle with the ends drilled to receive a clevis pin, which attaches the brake chamber push rod to the brake slack adjuster (ISO 9897 numerical code 90076)

Member that attaches to the upper (outer) landing gear legs and main frame structure to provide longitudinal & lateral stability. (ISO 9897 numerical code 91660)

Fitting used to seal the opening in an air brake hose connection (gladhand) when the connection is not in use; a dust cap (ISO 9897 numerical code 90220)

Pocket or tube to carry documents (for exaple registration papers) (ISO 9897 numerical code 90200)

Plastic or metal cover mounted on the landing gear to provide protection from road debris (ISO 9897 numerical code 90240)

Cushioning devices (rubber, plastics, wood, etc.) mounted at the extreme rear of chassis to take the initial impact of the vehicle when it backs into loading dock platform (ISO 9897 numerical code 90190)

Plastic or metal cover mounted on the brake spider to provide inner wheel protection from road debris (ISO 9897 numerical code 90230)

Valve or petcock fitted to the air reservoir or other low point in the air system to allow for drainage of moisture that may have condensed in the air system (ISO 9897 numerical code 90210)

Part of the chassis air brake system used by the driver to stop the vehicle in an emergency. Loss of air caused by a rupture in the system or by a breakaway will also cause an emergency brake application (ISO 9897 numerical code 90270)

Weather-protective covering of electrical connection (ISO 9897 numerical code 90912)

Kit containing the parts which retain the suspension equalizer within the equalizer hanger on tandem & tridem type suspensions. (ISO 9897 numerical code 91160)

"Receptacle (socket) designed to accept truck tractor electrical cable plug
Alternative: Seven-pin plug, 90720" (ISO 9897 numerical code 90250)

(See Electrical connector, 90250) (ISO 9897 numerical code 90720)

Part of the front bolster to which the electrical 7 way plug is attached. (ISO 9897 numerical code 91320)

Suspension device used to transfer and maintain equal load distribution between two or more axles of a suspension. Made to accommodate the ends of the spring (ISO 9897 numerical code 90810)

Combination valve in an air brake system, which controls brake application and which also provides for automatic emergency brake application should the trailer become disconnected from the towing vehicle (ISO 9897 numerical code 90660)

Assembly on the main rails that provides a convenient means of extending the length of a chassis to carry different-length containers [for example 12 m (40 ft), 13,5 m (45 ft), 14,5 m (48 ft)] (ISO 9897 numerical code 90260)

Spring loaded dirt/water protector on the 7 way electrical plug. (ISO 9897 numerical code 91610)

Ladder frame structure of the chassis (ISO 9897 numerical code 91480)

Part of the rear bolster to which the mud flap is bolted. (ISO 9897 numerical code 91240)

"Rigid structure mounted over tyres to prevent damage from debris picked up by the tyres
Alternative: Mudguard, 90570" (ISO 9897 numerical code 90280)

(See Fender, 90280) (ISO 9897 numerical code 90570)

Bracket used to mount the front of the suspension on the suspension subframe. Made to accommodate end of the spring (ISO 9897 numerical code 90830)

Protection for the inner tube in a tubed tyre (ISO 9897 numerical code 90290)

Locking mechanism which secures the chassis-extending assembly in any selected position (ISO 9897 numerical code 90296)

"Rolling pins or friction-inhibiting pads which facilitate movement of the chassis-chassisextending
assembly during extension or retraction" (ISO 9897 numerical code 90292)

Annual Federal chassis inspection per CFR. FHWA/FHWA Plate (Use DT OD and RT IP for inspection work) (ISO 9897 numerical code 91770)

Device welded to the main rails to prevent the two sliding parts of the main frame or the sliding suspension from pulling apart. (ISO 9897 numerical code 91500)

Part of the frame retaining the locking pin operating handle of a sliding main frame or suspension. (ISO 9897 numerical code 91520)

A type of light assembly mounted to the chassis by use of a special rubber grommet. (ISO 9897 numerical code 91620)

Rubber device used as the air seal between mating tractor and chassis airline connectors (gladhands). (ISO 9897 numerical code 91190)

Gooseneck doubler plate or gusset (ISO 9897 numerical code 91490)

Hubcap fitted on wheels having bearings lubricated with grease (ISO 9897 numerical code 90362)

Tubular insert, transition piece or bushing which separates one part (frequently a fastener) from another part for purposes of reduced friction, insulation, ease of assembly, etc. (ISO 9897 numerical code 90330)

Upper level of the front of a gooseneck chassis together with the structure connecting it to the lower level. The gooseneck rails fit into the tunnel recess of containers so constructed (ISO 9897 numerical code 90320)

Part of the fame used to guide the rails of a sliding main frame or suspension. (ISO 9897 numerical code 91510)

Mechanism through which landing legs are raised or lowered (ISO 9897 numerical code 90300)

Device used to retain grease lubricant in the bearing area of a wheel bearing lubricated with grease (ISO 9897 numerical code 90326)

A type of light assembly mounted to the chassis by use of a special rubber grommet. (ISO 9897 numerical code 91630)

Gusset or brace which stiffens a chassis bolster to resist longitudinal shocks (ISO 9897 numerical code 90055)

A structural member welded between the gooseneck main rails for lateral stability. (ISO 9897 numerical code 91370)

The lowest portion of the inner landing leg, which houses and retains the landing leg wheel/shoe axle (ISO 9897 numerical code 90432)

Transverse frame component used to stabilize motion of spring hangers (ISO 9897 numerical code 90855)

Cap that fits over the end of the axle to seal in lubricant and keep out road dirt. In an oil-bearing axle, is fitted with an oil-filling plug (ISO 9897 numerical code 90360)

A sealing device used between mating surfaces of the hub and hubcap to retain the wheel bearing lubricant. (ISO 9897 numerical code 91230)

"Connecting device at the rear of one vehicle used to pull a second semi-trailer or chassis by use of a convertor dolly
Alternative: Pintle hook, 90630" (ISO 9897 numerical code 90340)

(See Hitch, 90340) (ISO 9897 numerical code 90630)

Part of the rear bolster assembly used to attach the pintle hook assembly. (ISO 9897 numerical code 91550)

Device used to support brake hoses (component 90090) or brake lines (components 90092 and 90096) so they do not chafe on chassis components or pavement (ISO 9897 numerical code 90012)

Device positioned in the hub of the wheel on a chassis which records the mileage of the chassis (ISO 9897 numerical code 90370)

Attachment device at the rear used to connect the draw bar of a towing dolly. (ISO 9897 numerical code 91540)

Part of the pintle hook assembly used to retain the towing bar eye. (ISO 9897 numerical code 91560)

All of the parts of the locking pin on a sliding main frame or suspension. (ISO 9897 numerical code 91410)

Three lights at the rear in a horizontal row, mounted on the permanent structure near to the centreline and top of the vehicle (ISO 9897 numerical code 90380)

Device used to operate the locking pins on a sliding main frame or suspension. (ISO 9897 numerical code 91420)

Enclosure housing the locking pin assemblies on a sliding main frame or suspension. (ISO 9897 numerical code 91430)

Device that retracts the locking pins from the frame holes on a sliding main frame or suspension. (ISO 9897 numerical code 91530)

A structural member welded between the main rails for lateral stability. (ISO 9897 numerical code 91380)

Kingpin plate reinforcement framing and kingpin mounted on a chassis (also called “upper couples assembly” or “upper fifth wheel”) (ISO 9897 numerical code 90390)

Member that attaches to & between the bottom of the landing gear legs to provide lateral stability. (ISO 9897 numerical code 91400)

Part of the kingpin assembly that holds the kingpin in position (ISO 9897 numerical code 90420)

Attaching pin on a semi-trailer chassis that mates with and pivots within the fifth wheel of a truck tractor or convertor dolly while coupling the two units together (ISO 9897 numerical code 90400)

Shaft, turned manually by the landing gear handle, which works gearing to raise or lower the landing gear (ISO 9897 numerical code 90445)

Part of the kingpin assembly that rests on the fifth wheel of the truck tractor (ISO 9897 numerical code 90410)

Device, generally adjustable in height, used to support the front end of a container chassis in an approximately level position when disconnected from the towing vehicle (ISO 9897 numerical code 90430)

Steel support for landing legs in forward or aft direction or between the two legs (ISO 9897 numerical code 90460)

Plate exhibiting the registration number of a vehicle, mounted at the rear of a trailer (ISO 9897 numerical code 90540)

Member that attaches to & between the bottom of the upper (outer) landing gear legs to provide lateral stability. (ISO 9897 numerical code 91120)

Cylinder used to facilitate rotation of shafts in the landing gear assembly (ISO 9897 numerical code 90457)

Axle used to secure the sandshoe on the wheel to the landing leg (ISO 9897 numerical code 90520)

Box shaped structure welded to the main rail for attachment of the landing gear leg. (ISO 9897 numerical code 91460)

White light used to illuminate the licence plate (ISO 9897 numerical code 90550)

Handle for operating the landing gear mechanism (ISO 9897 numerical code 90440)

Inner part of the landing leg assembly (ISO 9897 numerical code 90490)

Gear which enables the landing legs to be raised or lowered at different speeds (ISO 9897 numerical code 90452)

Vertical adjustable supporting members of the landing gear, comprising an outer leg secured to the chassis frame and an inner leg, to which are attached sandshoes or wheels, which is raised or lowered by mechanical means (ISO 9897 numerical code 90470)

Bracket or box structure which protrudes from the main rail for the purpose of mounting a landing leg to the main rail (ISO 9897 numerical code 90455)

Flat plate or dish on the landing leg used to transmit the load to the ground (as an alternative to a wheel) (ISO 9897 numerical code 90500)

Outer part of the landing leg assembly (ISO 9897 numerical code 90480)

Lamp, lamp holder and attached wiring used for illuminating licence plate (ISO 9897 numerical code 90552)

Plate closing the end of a landing leg (ISO 9897 numerical code 90522)

Any round hollow pin which secures landing-gear gears to shafts (ISO 9897 numerical code 90458)

The translucent pat-t of a lamp assembly through which light passes. Commonly coloured red or amber or, for the licence plate light, white (ISO 9897 numerical code 90530)

Specialized chassis use only. Locking devices for multi-container carrying chassis. (ISO 9897 numerical code 91200)

Lights visible to the front or rear of a vehicle, mounted on the permanent structure of the vehicle as near as practicable to the upper left and right extreme edges, to indicate the overall width and height of the vehicle. The front and rear clearance lights of a the front and rear side marker lights, respectively container chassis are sometimes combined with the front and rear side marker lights, respectively (ISO 9897 numerical code 90160)

Threaded nut which retains a tyre and rim assembly on the wheel when fully torqued onto the wheel studs (after mounting over rim clamps in the case of chassis equipped with spoke-type wheels) (ISO 9897 numerical code 90555)

Wheel of the landing leg used to transmit the load on the landing gear to the ground (as an alternative to a sandshoes (ISO 9897 numerical code 90510)

Device which switches off heaters in case of excessive temperature (ISO 9897 numerical code 60858)

Shaft connecting the mechanism on the handle-side leg to the mechanism on the other leg (ISO 9897 numerical code 90450)

Bracket through which landing gear braces are fastened to an outer landing leg (ISO 9897 numerical code 90436)

A mud flap fastened to its attaching member. (ISO 9897 numerical code 91440)

Bracket or angle to which the mud flap is mounted (ISO 9897 numerical code 90565)

Curtain or shield at the rear of tyres to deflect downwards any splash guard, 90760 (ISO 9897 numerical code 90560)

(See Mudflap, 90560) (ISO 9897 numerical code 90760)

Other condenser devices not listed (ISO 9897 numerical code 60730)

Main longitudinal structural member(s) of a container chassis (ISO 9897 numerical code 90600)

A fixed-length member used to retain axle alignment. Normally one non-adjustable radius rod per axle is used (ISO 9897 numerical code 90840)

Hubcap fitted on wheels having bearings lubricated with oil (ISO 9897 numerical code 90366)

Device used to retain lubricant in the bearing area of the wheel. The sealing member of the seal is usually made of a resilient material such as synthetic rubber which is assembled into a wheel or hub bore (ISO 9897 numerical code 90590)

Bearing used with the anchor pins in S-cam type brake shoe installations (ISO 9897 numerical code 91170)

A plate on the rear bolster used for securement of the license plate. (ISO 9897 numerical code 91360)

Mechanically operated device normally used on a 12 m (40-ft) gooseneck container chassis in order to restrain a container during transport or transfer by the use of pins projected into the front apertures of the container’s bottom front corner fittings (ISO 9897 numerical code 90620)

Forward extension of the kingpin plate, usually turned upward to facilitate coupling of a truck tractor with the chassis (ISO 9897 numerical code 90610)

Rod which exists from chamber of the spring brake (component 90780) and extends outward upon brake application to rotate the brake slack adjuster and brake S-cam shaft, in turn engaging brake shoe lining and brake drum (ISO 9897 numerical code 90074)

Components of the equalizer and its hanger bracket used on tandem & tridem suspensions. (ISO 9897 numerical code 91710)

Bracket used to mount the equalizer beam of a multiple-axle spring suspension to the suspension subframe. Made to allow for the beam’s pivotal movement (ISO 9897 numerical code 90820)

Valve placed in the service brake line to accelerate the release of pressurized air in the line (ISO 9897 numerical code 90102)

Rubber pad between axle and U-bolt assembly (ISO 9897 numerical code 91745)

Hardware fitted to a frame member of a chassis and used to secure an air tank (ISO 9897 numerical code 90685)

Clamp mounted on wheel studs and secured by lug nuts which retains the rim assemblies on a spoke-type wheel (ISO 9897 numerical code 90692)

Devices used on vehicles to warn the driver of an approaching vehicle by reflecting light from the headlights of the approaching vehicle (ISO 9897 numerical code 90640)

Governmental registration of the vehicle, usually in paper form, kept in the document holder (ISO 9897 numerical code 90650)

Charge for over the road emergency repairs and associated service call and mileage fees. (ISO 9897 numerical code 91070)

The bracket used to mount the rear of the suspension on the suspension sub frame. Made to accommodate the end of the spring (ISO 9897 numerical code 90850)

Device inside ABS air valves used to keep debris from entering the air valve mechanisms (ISO 9897 numerical code 91280)

Marker, clearance and identification lights of a vehicle required by regulations (ISO 9897 numerical code 90700)

The part of a wheel assembly to which the tire is mounted and used only for tubeless type tires. (ISO 9897 numerical code 91140)

That part of the wheel on which the tyre is mounted and supported (ISO 9897 numerical code 90690)

A short metal tube with male threads both ends used to attach the service valve to the air reservoir. (ISO 9897 numerical code 91640)

Cylindrical rolling pins in the brake shoe assembly which, upon brake application, roll along the S-cam of the brake S-cam shaft, spreading the brake shoes apart, and causing contact of brake shoes and brake drum (ISO 9897 numerical code 90103)

Spring clip device that holds the lens in place in flange mounted lights. (ISO 9897 numerical code 91130)

Member used to retain axle alignment and, in some cases, control axle torque. It may be extended or retraced for alignment purposes. Normally one adjustable radius rod per axle is used (ISO 9897 numerical code 90800)

Pressure vessel used to store compressed air for several applications of the vehicle service brakes. Also called “air tank” (ISO 9897 numerical code 90680)

An alternating combination of red and white reflective identity stripes. (ISO 9897 numerical code 91590)

Control unit used to accelerate the application and release of air pressure in a part of the air brake system (ISO 9897 numerical code 90670)

Ring which fills the void between two adjacent rims for wheels fitted with dual tyres. fixing the position of each rim in the transverse (lateral) direction (ISO 9897 numerical code 90696)

Assembly consisting of two lined brake shoes, brake rollers, and miscellaneous hardware including brake anchor pin, other pins, and springs (ISO 9897 numerical code 90108)

Device that keeps S-cam type brakes within their proper adjustment range through normal brake applications. (ISO 9897 numerical code 91090)

Unit which uses the stored energy of springs to actuate brakes (ISO 9897 numerical code 90780)

Computerized control module in an antiskid brake assembly (ISO 9897 numerical code 90017)

Undercarriage with a subframe having provision for convenient fore-and-aft adjustment of its location on the chassis (ISO 9897 numerical code 90750)

Curved, flange-stiffened metal plate with friction-absorbing material attached, which contacts the brake drum to cause braking (ISO 9897 numerical code 90106)

Longitudinal structural members of the slider assembly sub frame and any associated cross-members (ISO 9897 numerical code 90905)

Light bulb for lights (ISO 9897 numerical code 90120)

Lights mounted on the rear at the right and left sides of a container chassis which indicate an intended change in direction by giving flashing warning signals on the side toward which the turn will made (ISO 9897 numerical code 90970)

Any of the springs in a foundation brake (ISO 9897 numerical code 90917)

Part of the mechanism of a sliding main frame or suspension. (ISO 9897 numerical code 91750)

Device which, when incorporated into a service brake system, automatically controls the degree of rotational wheel slip at one or more wheels of an undercarriage during braking (ISO 9897 numerical code 90018)

Lights which show to the side of a vehicle, mounted to indicate the overall length of the vehicle. They may also be mounted at intermediate locations on the sides (ISO 9897 numerical code 90730)

A doubler plate welded to the main frame web to reinforce the locking pin holes for sliding main frame or suspension chassis. (ISO 9897 numerical code 91700)

Device used to lock both parts of a sliding main frame or suspension in place. (ISO 9897 numerical code 91690)

Lights giving warning to indicate that the vehicle brakes are being applied (ISO 9897 numerical code 90890)

Device welded to the guide rails to prevent the two sliding parts the sliding suspension from pulling apart. (ISO 9897 numerical code 91680)

Sliding suspension guide rail attached to the main frame with mechanical fasteners. (ISO 9897 numerical code 91670)

Hose which transmits the brake-actuating signal from the tractor to the chassis brake valve(s) (ISO 9897 numerical code 90096)

Spring components of the spring suspension assembly (ISO 9897 numerical code 90860)

Suspension component used to support and locate the spring on the axle (ISO 9897 numerical code 90870)

Suspension using one or more cambered steel leaves to absorb road shocks from the axle and transfer loads through suspension components to the suspension subframe. Consists of the components 90800 to 90870 (ISO 9897 numerical code 90790)

Lug, attached to the frame of a chassis, used to secure the slider lock handle in place when not in use (ISO 9897 numerical code 90759)

Type of wheel consisting of integral hub and spokes designed to accept demountable rims, either singly or in pairs with a rim spacer for dual tyres (ISO 9897 numerical code 91030)

Mechanism which secures the slider assembly in any selected position (ISO 9897 numerical code 90752)

Any pin in the slider locking pin assembly which inserts through a hole in a main rail to secure the slider assembly to the main rails (ISO 9897 numerical code 90755)

Operator’s handle in the slider locking pin assembly, used to disengage the slider locking pins from the main rails (ISO 9897 numerical code 90758)

"a) Tubed: Tyre complete with inner tube, flap/boot
b) Tubeless: Tyre complete with valve" (ISO 9897 numerical code 90920)

Inner tube for tubed tyre (ISO 9897 numerical code 90960)

Rack for carrying a spare tyre, usually mounted below the main chassis frame (ISO 9897 numerical code 90930)

Lug, attached to the frame of a chassis, used to secure the twist-lock or pin-lock handle in place when not in use (ISO 9897 numerical code 90991)

Hand-operated part of the twist lock which permits turning of the shaft; i.e. locking and unlocking of the twist lock and identification of its correct positioning (ISO 9897 numerical code 90990)

Light used to show the rear of a vehicle (ISO 9897 numerical code 90910)

Shim used to raise the elevation of a twist-lock above the frame of a chassis (ISO 9897 numerical code 90992)

Combination of the stop, tail and/or turning lights in the same housing (ISO 9897 numerical code 90900)

The replaceable part of a light assembly that glows when electricity is applied to it. (ISO 9897 numerical code 91150)

A brand new tire. (ISO 9897 numerical code 91450)

Protective enclosure for twist-lock components (ISO 9897 numerical code 90993)

Bracket on the rear bumper used to mount the tail lights and/or protect the tail lights from impact by use of a protruding flange (ISO 9897 numerical code 90915)

Part of a gooseneck chassis at the transition between the main rails and the gooseneck (ISO 9897 numerical code 90950)

Valve for tubeless tyre (ISO 9897 numerical code 90940)

Mechanical device located at the corners of certain designs of container chassis which, when rotated into a locked position with the bottom corner fitting of a container, prevents container disengagement (ISO 9897 numerical code 90980)

A pair of structural member welded between the main rails for lateral stability at the suspension. (ISO 9897 numerical code 91390)

Assembly consisting of two bolts in the shape of a U, a spacer, and a saddle which secures the axle to the spring seat (ISO 9897 numerical code 90880)

Component used to raise the spring a pre-determined height above the axle. (ISO 9897 numerical code 91730)

Channel in the U-bolt assembly which supports the curved upper portion of the U-bolt and permits springs, spring seat, and axle to be clamped together (ISO 9897 numerical code 90885)

Device used to assemble the springs and torque rod attachment brackets to the axle. (ISO 9897 numerical code 91720)

Threaded cover to protect the end of the valve stem (ISO 9897 numerical code 90995)

Specialized chassis applications only. Air ride shock absorber assembly common on trailer equipment only (ISO 9897 numerical code 91740)

Device used to keep debris from entering the air system. (ISO 9897 numerical code 91290)

Lockwasher which sits adjacent to a wheel bearing or axle retention nut and helps maintain the bearings in proper position (ISO 9897 numerical code 91020)

Machined parts, usually roller bearings, designed to reduce friction between the axle spindle and also support the load while rotating at high speeds (ISO 9897 numerical code 91000)

Part of the wiring harness. (ISO 9897 numerical code 91600)

Harness encompassing a complete wiring system for chassis, including a wire for each separate circuit, and a ground (earth) wire; or any separate wire or portion of a wire within that harness (ISO 9897 numerical code 91060)

One of a pair of bearing assemblies used to mount the hub to the axle. (ISO 9897 numerical code 91300)

One of a pair of bearing assemblies used to mount the hub to the axle. (ISO 9897 numerical code 91310)

Part of the electrical wiring connecting the front & rear lights to the main wire harness. (ISO 9897 numerical code 91330)

Threaded bolt or shaft integrally mounted in the wheel, used to attach the rims to the wheel (ISO 9897 numerical code 91040)

Tank in which condensed refrigerant may be stored (ISO 9897 numerical code 62250)

Plate or angle which reinforces and stiffens connections of main frame cross-member flanges and main rails (ISO 9897 numerical code 90188)

Transverse member in the chassis main frame (ISO 9897 numerical code 90185)

The complete mechanism that keeps the door secured closed (ISO 9897 numerical code 10510)

A device attaching the locking bar to the top and bottom of a door, usually containing a bushing (ISO 9897 numerical code 10520)

The part of the door securing device that engages the retainer, which, by a lever action, forms the cam lock (ISO 9897 numerical code 10530)

A protective cover over the customs seal (ISO 9897 numerical code 10580)

A component, intermediate to the locking bar brackets, which holds the locking bar to the door in proper alignment (ISO 9897 numerical code 10540)

A component attached to the locking bar rod by mean of the lug, which, by turning, operates the assembly (ISO 9897 numerical code 10550)

A component, part of the locking bar rod to which the locking bar handle is secured (ISO 9897 numerical code 10560)

Nut used to secure locking bar hardware (ISO 9897 numerical code 10575)

The vertical shaft or rod to which the cam locks are fitted (ISO 9897 numerical code 10570)

Structural fastener secured with a collar that is swaged to the bolt (ISO 9897 numerical code 11910)

The fastener with which the locking bar handle is secured to the locking-bar lug (ISO 9897 numerical code 10565)

Device which indicates the running condition of the refrigeration unit (ISO 9897 numerical code 61740)

"Hardware used to secure sill to end frame for collapsible end frame of platform-based
container" (ISO 9897 numerical code 10577)

Pin securing end frame to side rail for collapsible end frame of platform-based container (ISO 9897 numerical code 10578)

Pin securing sill to corner fitting for collapsible end frame of platform-based container (ISO 9897 numerical code 10576)

Cargo tie-down fittings fixed to any part of the container for the attachment of straps or other devices to restrain movement of cargo (ISO 9897 numerical code 10230)

Bar for the attachment of straps or other devices to restrain movement of cargo (ISO 9897 numerical code 10240)

Part of the securing device assembly to which straps or other lashings are secured to restrain cargo movement (ISO 9897 numerical code 10250)

Owners address decal fitted to container (ISO 9897 numerical code 40302)

Marker used to identify either the service or the emergency air line gladhand. (ISO 9897 numerical code 91580)

Tag for mounting the airline marker to the gladhand. (ISO 9897 numerical code 91570)

Motor assembly excluding the compressor items (ISO 9897 numerical code 60250)

Motor assembly to revolve the fan (ISO 9897 numerical code 60560)

Motor assembly to revolve the fan (ISO 9897 numerical code 60860)

Warning sign of oversize and or electrical danger, in accordance with ISO 6346:1984, Annex C (ISO 9897 numerical code 40080)

Code designating the country of registration of the owner, in accordance with ISO 3166 (ISO 9897 numerical code 40010)

A marking required of a container that is operated under an approved continuous examination programme prescribed in the CSC (ISO 9897 numerical code 40210)

Caution marking indicating 9ft6in height (ISO 9897 numerical code 40082)

Entire chassis, including sliding mechanism and running gear (ISO 9897 numerical code 90138)

Entire container (ISO 9897 numerical code 12000)

Marking of classification societies and other organizations approved by the competent authority (ISO 9897 numerical code 40220)

Users logo or decal (ISO 9897 numerical code 40310)

Caution marking indicating over width (ISO 9897 numerical code 40084)

Pocket or tube to carry documents (ISO 9897 numerical code 62745)

Entire set of markings on a container (ISO 9897 numerical code 40100)

Alternating oblique striped marking fitted to upper rails used to distinguish 1AAA, 1BBB and 1CCC (high-cube) containers (ISO 9897 numerical code 40072)

Optional height marks for containers of height greater than 2,6 m (8,5 ft), in accordance with ISO 6346:1984, Annex H (ISO 9897 numerical code 40070)

Other compressor-motor devices not listed (ISO 9897 numerical code 60330)

Owner’s code, 40040; serial number and check digit, 40050; size and type code, 40060; in accordance with ISO 6346 (ISO 9897 numerical code 40020)

Maximum gross and tare weights, in accordance with ISO 6346; playload (ISO 9897 numerical code 40030)

Owner’s mark, in accordance with ISO 6346 (ISO 9897 numerical code 40040)

Owner’s logotype (ISO 9897 numerical code 40300)

Plate on which customs approval data is displayed (ISO 9897 numerical code 40230)